Zontes ZT250-R Скачать руководство пользователя страница 12

Страница: 12 / 76

1-FRAME&ELECTRONIC COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1274100-012000 ZT250

－

S Pedal axis pin

1274200-061000 ZT310

－

X rear right footrest

1264100-005000 ZT250

－

S Pedal Steel ball spring

1264100-006000 ZT250

－

S Pedal clamp spring

1274100-010000 ZT250

－

S Rear pedal steel ball

1274100-052000 ZT250

－

S Rear pedal locating plate

1274200-062000 ZT310

－

X rear left footrest

1251100-101000 Non

－

standard bolt M6×12 (304 stainless steel)

1274100-100000 ZT250

－

R disc brake lock bracket

【

】

1250303-010093 GB6177.1M6(color zinc )

1244200-024000 ZT310

－

X footrest gum cover

1274200-051000 ZT310

－

X footrest gum cover fixed plate

1250205-038000 GB70.2M5×12(stainless steel)

1032142-040000 ZT310

－

X rear left pedal

1032142-039000 ZT310

－

X rear right pedal

1250501-010000

GB93φ6 spring pad

PROCEDURE:

●

Dissembly rear pedal

Pry open the clamp spring

⑷

, then push the pedal pin shaft

⑴

out with tools.Pull the pedal

⑵

⑺

outward.

●

Assemble rear pedal

Place one side with two holes of pedal horizontally and put the pedal spring

⑶

in the pedal

⑵

⑺

in the small hole.

Put the steel ball

⑸

inside,compress the steel ball and spring with the positioning plate

⑹

Assemble the pedal on the frame and distinguish the right, left pedal.
The axis pin

⑴

is inserted after the pedal hole is aligned with the pedal support mounting hole.

Insert the clamp spring

⑷

into the pin shaft slot.

●

Disc brake lock bracket

Fix the bolt

⑻

with a hexagonal tool and remove the nut

⑽

with a sleeve, and finally remove the disc brake lock bracket

⑼

from the frame.

●

Foot aftersales service parts

Grasp the left rear pedal

⒁

or right rear pedal

⒂

, remove the bolt

⒀

with an allen tool, and remove the spring washer

⒃

Remove the rubber sleeve

⑾

and the fixing piece

⑿

CAUTION

：

●

Take care of the material when removing the pedal.

●【

】

Only suitable for TOP DOG disc brake lock RE008 and TOP DOG disc brake lock RE0081, other models are not

adapted.

●【

】

Only for after-sales replacement of worn-out pedal parts.

【

】

Rear pedal component

FIG.6 FRAME&ELECTRONIC

PARTS COMPONENT

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды