Zontes ZT250-R Скачать руководство пользователя страница 59

Страница: 59 / 76

8-FUEL TANK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251200-033093 Non-standard nut (environmental color)

1251100-102000 Non-standard bolts M6×16 (304 stainless steel)

1224100-010000 Expansion nail

PROCEDURE:

●

Fuel tank middle cover assembly

Turn the Fuel tank cover and Fuel tank liner assembly upside down and remove the bolt (1).Be careful not to

close the Fuel tank cover and take care to protect the paint surface.

Remove the swell nail.

⑶

Remove the bolt (2) with the hexagonal tool and be careful not to pull the Fuel tank cover nylon rope

①

Pull back the middle cover assembly and remove it.

CAUTION:

●

Make sure the motorcycle is fixed during the process of discomponent.

●

Do not close the fuel tank cover and do not release the fuel tank cover when disassembling.

●

The torque of the self-tapping screw during reassembly should not be too large to prevent damage to the fuel

tank cover.

●

The material should be protected during the disassembly process to prevent damage to the paint surface.

FIG.2 FUEL TANK

COVER

Fuel tank middle cover assembly

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды