Zontes ZT250-R Скачать руководство пользователя страница 38

Страница: 38 / 76

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1154100-012000 ZT250

－

R clutch line (II)

FIG.2 FRONT FORK

COMPONENT

Replace the clutch line

PROCEDURE:

●

Disassemble the cluch line

Use an open-end wrench to loosen the bolt

②

and bolt

③

; fix the adjusting screw

①

, rotate the bolt

②

up to the

top of the thread of the adjusting screw, and screw the bolt

③

to the bottom to completely separate from the

thread. Separate the clutch wire core connector from the bracket

⑤

, close the bolt

③

to the black sheath with one

hand, and remove the adjustment screw

①

from the bracket

④

with one hand.

First, the protective rubber sleeve

⑨

is retracted to the elbow

⑧

and the nut

⑥

is loosened with the pliers; the nut

⑥

and the adjusting screw

⑦

are rotated to the same position as the groove on the rocker arm, and the cable is

pulled from the rocker arm seat. Finally remove it.

Remove the clutch line.
Remove the protective sleeve

⑨

from the clutch cable

⑴

●

Install the clutch

Put protective rubber sleeve

⑨

into clutch elbow

After inserting the clutch cable joint into the rocker arm, screw the nut

⑥

and the adjusting screw

⑦

to the

groove on the rocker arm.

Assemble the clutch cable into place according to the original alignment.
Rotate the nut

②

up to the top of the thread of the adjusting screw, and screw the nut

③

to the bottom to

completely separate from the thread.

Take the nut

③

close to the black sheath with one hand and insert the adjustment screw

①

into the bracket

④

with the other hand.

Insert the clutch core connector into the hole of the bracket

⑤

Initially position the nut

②

first, adjust the free stroke adjustment in the clutch cable adjustment, and then lock

the nut

③

Finally, reset the protective rubber sleeve

⑨

CAUTION:

●

The motorcycle support should be fixed during disassembly to prevent accidents caused by incline.

●

Before replacing the clutch line, it is necessary to disassemble the seat cushion, fuel tank, liner, side cover, etc.

Содержание ZT250-R













































































Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды

Zontes ZT250-R, Руководство по обслуживанию

Результаты поиска

Содержание ZT250-R

Отзывы:

Похожие инструкции для ZT250-R

Бренды по названию

Популярные бренды