ZIEHL-ABEGG ZETADYN 3C Скачать руководство пользователя страница 115

Страница: 115 / 204

11.7.2

Deceleration when traveling speed has not been reached

When the switch off point for the traveling speed is reached, the con

ﬁ

gured

ﬁ

nal speed

V_3 is not reached.
Deceleration is initiated

Travel at positioning speed V_1

Positioning speed V_1 is switched off.
Motor continues to decelerate.

Speed 0
Output MB is switched off
Brake must operate immediately
The motor continues to be fed with current

The current to the motor is switched off
Output RB is switched off
Motor contactors must drop immediately

Deceleration when traveling speed has not been reached

Controller enable

V_1

Positioning speed

V_3

Travel Speed

RV1 / RV2

Direction default

Controller ready

MB_Brake

Mechanical brake

Information

If the trip duration is monitored by the open loop control, due to the long trip time with a traveling speed
of V_1 an error message may result!

Information

If the traveling speed is switched off just before the preset

ﬁ

nal speed has been reached, it could

happen that the

ﬂ

oor is overshot.

Original operating instructions

ZETADYN 3C

Travel options

R-TBA08_03-GB 1619

Part.-No. 00163322-GB

115/204

Содержание ZETADYN 3C













































































































































































































Результаты поиска

Содержание ZETADYN 3C

Отзывы:

Бренды по названию

Популярные бренды

ZIEHL-ABEGG ZETADYN 3C, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание ZETADYN 3C

Отзывы:

Бренды по названию

Популярные бренды