TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 92

Страница: 92 / 138

ID Separation

The host can select a unique ID separation of one ID or two IDs. The reader default operation is for a

unique ID separation of one ID and a uniqueness timeout of two minutes. You can disable the uniqueness

check using Command

#40

Transmit All ID Codes

. In this case, every tag ID received is transmitted

without regard to uniqueness. You can reinstate uniqueness checking with commands

#4100

#4101

Select ID Separation.

Note:

The MPRX internal timing varies depending on the operative tag read mode and the type of

tag in the read field.

Refer to section

“40 Transmit All ID Codes” on page 5–63

“and section

“529 Display Presence Input

Status” on page 5–70

To set ID separation parameters

1. Ensure that the host device is in command mode.
2. Enter Command

#4100

to select a separation of one ID; enter Command

#4101

to select a

separation of two IDs. Press ENTER.

Reports

The MPRX can be configured to transmit presence without tag reports and input status change reports.

A presence without tag report is transmitted in data mode only, and only if the system has a presence

detector. This report is sent if a presence is detected without the detection of a valid tag ID. Refer to

sections

“529 Display Presence Input Status” on page 5–70

and

“690N Select Presence Without Tag

Report Option” on page 5–78

To set presence reporting

1. Ensure that the host device is in command mode.
2. Enter Command

#529

to display presence input status and press ENTER. P0 indicates presence

without tag reports disabled (factory default), and P1 indicates presence without tag reports

enabled.

3. Enter Command

#6901

to enable presence without tag reports, or enter Command

#6900

disable presence without tag reports (factory default). Press ENTER.

To set input status change reporting

1. Ensure that the host device is in command mode.
2. Enter Command

#560

to display input status change report options and press

ENTER.

input status change reports disabled (factory default)

input status change reports enabled

reporting disabled (factory default)

changes on input 0 reported

changes on input 1 reported

changes on either input reported

MPRX User Guide

TransCore Proprietary

6–92

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды