TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 71

Страница: 71 / 138

752 ms

RF timeout infinite, never expires (factory default)

input inversion disabled (factory default)

input inversion enabled

For

example, if factory default settings are assigned, the reader message is

PRST P0 D0 A2 TF I0

which means that presence without tag reports is disabled, minimum presence true period is 0, RF off

control on timeout or presence false, infinite RF timeout, and input inversion disabled.

530 Display RF0 Filter Status

#530

displays the parameter set for the RF input, including the selected unique ID code

criteria (

#410N

Select Unique ID Code Criteria) and the valid ID code criteria, which

are fixed at one acquisition.

Reader response

RF0S U<0 to 4> V<0 to 3>

where

One ID separation (factory default)

Two ID separations

Three ID separations

Four ID separations

Transmit all IDs

Valid ID code criteria of one acquisition (factory default)

Valid ID code criteria of two acquisitions

Valid ID code criteria of three acquisitions

Valid ID code criteria of four acquisitions
For example, if factory default settings are assigned, the reader message is

RF0S U0 V0

which means separation of one ID for uniqueness filtering and a valid ID code criteria of

one acquisition.

534 Display Tag Translation Mode Status

#534

displays tag translation mode status, enabled or disabled. If tag translation mode is

enabled, incoming full-frame tags in AAR or ATA format are translated according to

ISO standards. Refer to

“452 Disable Tag Translation Mode (Factory Default)” on page

5–65

and

“453 Enable Tag Translation Mode” on page 5–65

for more information.

Reader response:

TT <0 to 1>

where

tag translation mode disabled

tag translation mode enabled

Chapter 5 Commands

TransCore Proprietary

5–71

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды