TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 70

Страница: 70 / 138

which means that RF is enabled by presence sensor on input 0, RF signal off, uniqueness timeout of two

minutes, RF output frequency has not been set, maximum RF output range for ATA tags, maximum RF output

range for eGo and eGo Plus tags, full RF power, and IAG power set at 4 dB attenuation.

529 Display Presence Input Status

#529

displays the parameters associated with presence detection and RF control. The

reader’s message indicates if presence without tag reports are enabled/ disabled

(

#690N

Select Presence without Tag Report Option), if input inversion is enabled/

disabled (#

694N

Select Input Inversion Option), and the minimum presence true

period (always true). The reader’s message also reports the selected RF timeout

(

#693N

Select RF Timeout Period) and the selected means of RF-off control (

#692N

Select RF Control Algorithm). If presence without tag reports is enabled (

#6901

Enable

Presence without Tag Report Option), the reader transmits a report if a presence is

detected without the subsequent acquisition of a valid tag.

Note:

RF timeout values vary depending on the operative tag read mode and the type of tag in the

read field. All times are approximate.

Reader response:

PRST P<0 to 1> D0 A<0 to 2> T<0 to F> I<0 to 1>

where

Presence without tag reports disabled (factory default)

Presence without tag reports enabled

Minimum presence true period of 0 ms (fixed)

RF off on timeout only

RF off on timeout or tag

RF off on timeout or presence condition false (factory default)

RF timeout of 0 ms (always expired)

4 ms

8 ms

12 ms

20 ms

24 ms

32 ms

48 ms

60 ms

92 ms

152 ms

300 ms

452 ms

600 ms

MPRX User Guide

TransCore Proprietary

5–70

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды