TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 47

Страница: 47 / 138

<cmd>

Command code, a string that contains from two to four ASCII hex characters

[<data>]

Optional data field, an ASCII string of as many as 20 characters in length. For example,

the store hardware configuration string command is

#696S...S

or command

#696

Store Hardware Configuration String followed by the data string

S...S

<crc>

CRC value for the message

<eom>

End-of-message character (ASCII CR)

Reader Command Response

The basic protocol format is

The ECP format is

where

<som>

Start-of-message (ASCII # character)

<seq>

Echo of sequence number received in host command message

<resp>

Response string. The MPRX returns

#Done, #Error,

or another ASCII string

depending on the host transmission. This string can be up to 72 characters long.

<crc>

CRC value for the message

<eom>

End-of-message character (ASCII CR and LF)

Sample Messages

This section contains examples of typical messages transmitted between the MPRX and the host device.

Reader Transmissions

Basic protocol reader transmission

#KING 1302<eom>

Host response

No host response for non-ECP

ECP reader transmission

#4KING 1302 <crc><eom>

Chapter 4 Communications Protocols

TransCore Proprietary

4–47

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды