TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 125

Страница: 125 / 138

Table 38 MPRX Commands Listed Alphabetically

Command Name

Number

Reader Message

Disable eATA

488

#Done

if MPRX model supports

this tag protocol,

#Error

if tag

protocol is unsupported

Disable echo mode

6170

#Done

Disable flow control

6140

#Done

Disable input inversion (default)

6940

#Done

Disable MPRX mode

836

#Done

Disable multi-tag sort (default)

454

#Done

Disable parity (default)

1020

#Done

Disable presence without tag

reports (default)

6900

#Done

Disable SeGo

484

#Done

if MPRX model supports

this tag protocol,

#Error

if tag

protocol is unsupported

Disable SeGo protocol tag

initialization during multi-tag sort

457

#Done

Disable tag translation mode

(default)

452

#Done

Display appended info status

524

IDAP T<0 to 1> D<0 to 1>

X<0 to 1>

Display boot checksum

543

BCKS xxxx

Display comm port parameters

522

MAIN B<2 to 7> S<0 to 1>

P<0 to 2> D0

Display comm protocol

525

ECPS P<0 to 2> T<01 to

FF> X<0 to 2> S0

Display echo status

537

ECHO <0 to 1>

Display flash checksum

540

PCKS I0000 Exxxx

Display hardware configuration

information

506

S...S (Max 20 characters)

Display input status change

560

SSTC E<0 to 1> M<0 to 3>

Display operating mode status

570

ATA:<E, D> eGo:<I, F, D>

SeGo:<I, F, D> IAG:<E, D>

Sort:<E, D> TMM0

Display power fail bit

520

PWRB P<0 to 1> R0

Appendix D Command Quick Reference

TransCore Proprietary

D–125

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды