TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 103

Страница: 103 / 138

Table 29 Symptoms and Remedies

Symptom

Number

Symptom

Remedy

The read zone is too

small, even before the RF

power and range control

have been adjusted.

If another MPRX is in the same area, ensure that it is operating on

another frequency that is at least 2 MHz different.
Check for possible interference from another nearby RF source:

fluorescent lights, neon signs, high voltage power lines, nearby

cellular telephone, or radio stations. Lights will need to be removed

or shielded. Point the external antenna in a different direction to see

if interference comes from only one direction. You may require a

different MPRX that uses another frequency.
Verify that the RF power is set to an appropriate value. Verify that

the range adjustment is set to the maximum. Verify that the reader is

getting at least 12V (wayside), 24V (onboard).

The perimeter of the read

zone has been defined,

but there is a “hollow”

spot in the center of the

zone that does not read

tags.

The angle of the external antenna may need adjustment. Slightly tilt

the external antenna to a different angle to change either the length

or width of the read zone.
Check the range control adjustment. Refer to

“Radio Frequency” on

page 6–93.

The MPRX is reading tags

out of the desired read

zone.

Some interference from other RF or electrical sources may be

occurring.
Verify that the read zone has been properly set up. Refer to

“Fine-

Tuning and Verifying the Read Zone” on page 6–97

b Use this number to reference the problem you are having with the MPRX if you contact Transcore for Technical Support.

MPRX Repair

The MPRX is designed for whole-unit replacement and is manufactured with surface-mounted

components. It requires sophisticated testing and repair equipment. All testing and repairs are performed

at TransCore’s factory. Please contact TransCore to obtain a Return Materials Authorization (RMA) for

returning the reader.

Technical Support

Authorized dealers and distributors are responsible for the direct support of all customers. Authorized

dealers and distributors needing support can contact TransCore Technical Support. Please be prepared

to answer a series of questions that are designed to direct you to the best TransCore support resource

available. These questions will relate to symptoms, configuration, model, and tags used.

Note:

End users and facility operators contacting Technical Support will be referred to the dealer

responsible for the system sale.

Chapter 7 Troubleshooting and Maintenance

TransCore Proprietary

7–103

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды