TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 57

Страница: 57 / 138

Command Mode

While the MPRX is in the command mode, the host device sends commands to the MPRX that can be

used to control the reader operation and configuration. After the MPRX receives a command, it transmits

a command response message. Typically, the command message contains

#Error, #Done

, or data

relating specifically to the command request. These messages may be of variable length since some

commands require information as part of the message; for example,

#570 Display Operating Mode

Status.

Communication can be lost if the host device attempts to send certain commands under marginal

communication conditions. For example, if the host device transmits the command request to change the

baud rate and the MPRX properly receives the request and transmits the

#Done

message, one of the two

following conditions may occur:

1. If the host device receives the

#Done

message, then both the host and the MPRX switch to the

new baud rate, and communications are maintained.

Note:

In many applications, the host must be set to the new baud rate as it does not change

automatically. The MPRX changes the baud rate immediately after issuing the message.

2. If the host does not receive the

#Done

message transmitted by the MPRX, the host assumes that

the command was not properly sent and does not switch to the new baud rate, causing a loss of

communications.

Caution

The host device should only change communications parameters or protocols during test or

set up conditions.

Download Mode

In download mode, the host can download new software to the MPRX.
While in download mode, the MPRX turns RF off, does not process tags, and does not echo host

commands.
Typically, TransCore trained personnel download new application code using a custom firmware loader

program. Contact TransCore Technical Support for information about firmware updates and procedures

Chapter 5 Commands

TransCore Proprietary

5–57

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды