TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 72

Страница: 72 / 138

537 Display Echo Status

#537

displays echo mode status. In basic protocol (

#610

Select Basic Communication

Protocol) and data inquiry protocol (

#613

Enable Data Inquiry Protocol), the reader may

be configured to enable

(#6171

Enable Echo Mode) or disable (

#6170

Disable Echo

Mode) the echo of received commands. Refer to sections

6170 Disable Echo Mode

and

“6171 Enable Echo Mode (Factory Default)” on page 5–75

for more information.

Reader response:

ECHO <0 to 1>

where

Echo status disabled (factory default)

Echo status enabled

540 Display Flash Checksum

#540

displays the flash memory checksum.

Reader response:

PCKS I0000 Exxxx

where

0000

Not applicable to the MPRX

xxxx

Represents the four-byte ASCII representation of the flash memory checksum

543 Display Boot Checksum

#543

displays the boot ROM checksum.

Reader response:

BCKS xxxx

where

xxxx

represents the four-byte ASCII representation of the boot ROM checksum.

549 Get User-Programmable Group Select Equals (GSE) Filter Data

#549

queries the reader for the user-programmable GSE filter data programmed in the

reader using Command

#697.

The response data is formatted similar to the data in the

configuration command.
For example, if the command string shown in Command

#697

(refer to

“697 Set User-

Programmable Group Select Equals (GSE) Filter” on page 5–81

) was sent to a given

reader, the response to the

#549

query command would be:

#A4 0A 0005014202024133

The reader response contains all the data fields repeated in the same sequence as

displayed in the User-Programmable GSE configuration command.

552 Display Antenna Multiplexing Mode

#552

displays the antenna multiplexing mode When the MPRX mode is enabled

Reader response:

MUX x<0 to 3> <MPRX>

where

x=0

antenna multiplexing disabled, RF on port 0 only

MPRX User Guide

TransCore Proprietary

5–72

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды