TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 76

Страница: 76 / 138

63 Reset Reader

#63

resets the power fail bit, clears all buffers, resets tag uniqueness, turns off both output

lines, transmits the sign-on message, and returns to the data mode.

Note:

This command does not reset any other configuration parameters.

Reader response:

Model E4 Series Ver X.XX SNSSSSSS
Copyright 2008 TransCore

where

X.XXD

Version number

SSSSSS

Serial number of the unit, skipping the fourth character printed on the reader product

label.

640N RF Control

#640N

directly controls the RF module. The N value controls the RF power as shown in

Table 20

Table 20 RF Control Commands

Command

RF Power

6400

Turns off RF

6401

Turns on RF

Note:

These commands only have an effect when the reader is not in MPRX mode. Refer to

Commands

#836

and

#837

#6400

disables RF-by-input control command

#641

Select RF-by-Input Control.

Reader response:

#Done

641 Select RF-by-Input Control (Factory Default)

641

configures the reader for RF-by-input control. The reader automatically turns on RF

when it detects a presence through sense 0. The reader turns off RF according to the

selected RF control algorithm (

#692N

Select RF Control Algorithm).

Note:

This command only has an effect when the reader is not in MPRX mode.

Reader response:

#Done

643NN Select ATA Operating Range (Distance)

#643NN

selects the read range for ATA tags where

is a hexadecimal value from 00 to 1F; the

range increases with increasing

value. The range can be adjusted for 32 discrete

values where 00 is the shortest range and 1F is the longest range. The default range

value is 1F.

Reader response:

#Done

MPRX User Guide

TransCore Proprietary

5–76

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды