TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 79

Страница: 79 / 138

692N Select RF Control Algorithm

#692N

selects the algorithm for turning off RF power when RF-by-input control is enabled

using Command

#641

Select RF-by-Input Control.

The values for

specify the RF control algorithms as shown in

Table 23

Table 23 RF Control Algorithm Commands

Command

RF Power Off

6920

On timeout only

6921

Timeout or tag ID acquired

6922

Timeout or presence false (factory default)

#6920

turns off RF power based on the timeout established by Command

#693N

Select RF

Timeout Period.

#6921

allows RF power to be turned off either after the timeout period or upon acquisition of a

valid tag ID, whichever occurs first.

#6922

turns off RF power either after the timeout period or upon the presence false condition,

whichever occurs first.

Reader response:

#Done

693N Select RF Timeout Period

#693N

selects the RF timeout period used by Command

#692N

Select RF Control Algorithm.

Values for N range from 0 through F.

#693F

disables the RF timeout. The reader turns off the RF immediately following the

acquisition of a valid tag, whether or not it is unique.

Uppercase or lowercase characters are allowed for N; for example, hex digits A through F or a through f.

The commands and corresponding timeouts are shown in

Table 24

Table 24 Timeout Period Values

Command

Timeout (ms)

6930

0 (always expired)

6931

6932

6933

6934

6935

6936

6937

Chapter 5 Commands

TransCore Proprietary

5–79

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды