TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 95

Страница: 95 / 138

•

Enter Command

#641.

Press ENTER.

•

Leave the setting on RF-by-input control for normal operation.

Sense Inputs

The RS–232 configuration used by the MPRX has two sense inputs — SENSE 0 and SENSE 1. SENSE 0

is used to enable RF on antenna ports 0 and 1 if enabled, and SENSE 1 is used to enable RF on antenna

ports 2 and 3. The sense input circuits are used to notify the MPRX of train presence and are designed to

be connected to a free-of-voltage dry contact. The MPRX sense inputs are designed to connect to a dry

contact closure.
You can configure the MPRX to generate input status change reports, which are transmitted like tag IDs.

The host can then respond based on the true/false (closed/open) status of the sense inputs. Refer to the

section

“Reports” on page 6–92

“.

The following procedures describe how to set sense inputs using the terminal emulation software. Refer to

command

“694N Select Input Inversion Option” on page 5–80

for more information.

To set sense inputs

1. Ensure that the host device is in command mode.
2. Enter Command

#6940

to disable input inversion (factory default) or Command

#6941

to enable

input inversion, and press

ENTER

Sense Output Device

The sense output is dedicated for testing and set up of the reader. It is defined as the TAG_LOCK signal

and indicates that a valid tag is in the read field.
This sense output is a dry contact that provides a normally open and normally closed sense output. The

relay contacts are rated at 42.2V AC peak (30 Vrms) or 60V DC at 1 A maximum. If controlling an external

gate or device requiring high current, an isolation transformer is required.

Serial Port Communications

The MPRX supports one RS–232 communications port. For the RS–232 communications specification, the

MPRX maintains the following three sets of parameters that affect serial port communications:

•

Port configuration parameters (baud rate, data bits, stop bits, parity)

•

Communications protocols (basic, error correcting)

•

Flow control scheme (none, software)

The default serial port configuration for each of these three parameters is as follows:

•

9600 baud, 8 data bits, 1 stop bit, no parity

•

Basic communications protocol

•

Software flow control (XON/XOFF)

You can change these parameters in data mode and command mode operation by issuing commands

with the host device. Use the following procedures to set serial port communications parameters using the

terminal emulation program.

Chapter 6 Configuration

TransCore Proprietary

6–95

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды