TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 58

Страница: 58 / 138

Command List

Reader commands are divided into groups based on a primary function. The following sections provide

information about each command in command number order. Refer to

“Command Quick Reference” on

page D–116

for listings of commands in numerical and alphabetical order.

In the following text, the symbols

<and>

represent variable message data. These symbols are not part of

the message syntax.
Hex digits (0–9, A–F) in either uppercase or lowercase characters may be used in data strings and for hex

digits A–F.

Reader Mode Control — Command Group 0

Group 0 commands control reader mode. The mode determines whether the reader is transmitting data to

or receiving data from a host device or terminal.

00 Switch to Data Mode (Factory Default)

#00

switches the reader to data mode, which allows the reader to transmit tag data (ID

codes) to the host. In addition to switching the reader to data mode, Command

#00

automatically saves to non-volatile memory (NVRAM) any user parameters that had

been changed during the command mode session. The reader enters data mode on

power up.

Caution

To save user parameter changes to non-volatile memory (NVRAM), you must send Command

#00

before powering down the reader.

When MPRX mode has been enabled (

#837

) and while the MPRX is in data mode, the host device can

send the following commands to the MPRX:

#01

Switch to Command Mode

Reader response:

#Done

#440

Reset Uniqueness

Reader response:

#Done

#8110

Switch on RF port 0, Fire Off Check Tag Address 0 on Check Tag pin 0

Reader response:

#Done

#8111

Switch on RF port 1, Fire Off Check Tag Address 1 on Check Tag pin 0

Reader response:

#Done

#8112

Switch on RF port 2, Fire Off Check Tag Address 0 on Check Tag pin 1

Reader response:

#Done

#8113

Switch on RF port 3, Fire Off Check Tag Address 1 on Check Tag pin 1

Reader response:

#Done

#8150

Set Check Tag Address to 0 on Check Tag pin 0.

Reader response:

#Done

MPRX User Guide

TransCore Proprietary

5–58

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды