TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 73

Страница: 73 / 138

x=1

antenna multiplexing between RF ports 0 and 1 when sense 0 active

x=2

antenna multiplexing between RF ports 0 and 1 when sense 0 active and RF port 2

when sense 1 active

x=3

antenna multiplexing between RF ports 0 and 1 when sense 0 active and RF ports 2

and 3 when sense 1 active

MPRX =

MPRX mode selected

560 Request Sensor Status Change

#560

displays the sensor status change reporting. Not applicable to the MPRX

Reader response:

SSTC E<0 to 1> M<0 to 3>

where

Input status change reports disabled (factory default)

Input status change reports enabled

Reporting disabled (factory default)

Changes on input 0 reported

Changes on input 1 reported

Changes on either input reported

For example, if factory default settings are assigned, the reader message is

SSTC E0 M0

which means that input status change reports are disabled on both input 0 and input 1.

570 Display Operating Mode Status

#570

displays the currently selected tag read mode.

Reader response:

ATA:<E, D> eGo:<I, F, D> SeGo:<I, F, D> IAG:<E, D> Sort:<E, D> TMM0

where

ID (64 bits)

Enabled

Full transaction (eATA)

Disabled

TMM0

Fixed

577 Report Buffered Handshakes

#577 r

eports the buffered handshakes. When in MPRX mode and/or if antenna multiplexing

is enabled, the response is

Reader response:

HDSH C0 <ww> C1 <xx> C2 <yy> C3 <zz>

where

count from port 0

count from port 1

Chapter 5 Commands

TransCore Proprietary

5–73

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды