TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 59

Страница: 59 / 138

#8151

Set Check Tag Address to 1 on Check Tag pin 0.

Reader response:

#Done

#8152

Set Check Tag Address to 0 on Check Tag pin 1.

Reader response:

#Done

#8153

Set Check Tag Address to 1 on Check Tag pin 1.

Reader response:

#Done

Note:

The MPRX transmits ID codes to the host device when the MPRX is in data mode.

01 Switch to Command Mode

#01

switches the reader to command mode, which allows the reader to accept commands

from a host or terminal. While in command mode, the reader turns RF off and does not

acquire tags.

Reader response:

#Done

Communications port Control — Command Group 1

Group 1 commands configure the parameters used by the MPRX to communicate with a host device or

terminal. These commands set baud rate, stop bits, parity, and end-of- line delay.

100N Select Baud Rate

#100N

selects the reader baud rate. The factory-default setting is 9600 baud. The N variable

specifies the baud rate shown in

Table 12

Table 12 Select Baud Rate Commands

Command

Baud Rate Selected

1002

1200

1003

2400

1004

4800

1005

9600 (factory default)

1006

19.2 K

1007

38.4 K

Reader response:

#Done

Caution

If ECP is enabled, ensure that the ECP timeout is sufficient for the new baud rate.

101N Select Stop Bits

#101N

selects the number of stop bits for reader character transmission. The factory default

setting is 1 stop bit. The N variable specifies the number of stop bits as indicated in

Table 13

Chapter 5 Commands

TransCore Proprietary

5–59

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды