manualshive.com logo in svg

TransCore MPRX 10-7200-001, Руководство пользователя

Поделиться
Скачать
TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 96

Port Configuration Parameters

Use this procedure to set port configuration parameters using the terminal emulation program. Refer to 

sections 

“100N Select Baud Rate” on page 5–59

 through 

“102N Select Parity” on page 5–60

.

To set baud rate

1.  Ensure that the host device is in command mode.
2.  Enter Command 

#100N

 and press 

ENTER

.

To set stop bits

1.  Ensure that the host device is in command mode.
2.  Enter Command 

#101N

 and press 

ENTER

.

To set parity

1.  Ensure that the host device is in command mode.
2.  Enter Command 

#102N

 and press 

ENTER

.

Communications Protocol

Use the following procedures to set communications protocol. Refer to sections 

“610 Select Basic 

Communication Protocol (Factory Default)” on page 5–74

  through 

“614N Select Software Flow Control 

Option” on page 5–75

 for more information.

Caution

Do not switch to ECP (Command #611) unless the host is prepared to acknowledge 

each reader transmission.

To select a communications protocol

1.  Ensure that the host device is in command mode.
2.  Enter Command 

#610 

to select basic protocol (factory default) or Command 

#611 

to select ECP 

and press ENTER.

Software Flow Control

The host can enable or disable software flow control with Command 

#614N

 Select Flow Control Option.

The host can use software control characters (XON/XOFF) to interrupt reader transmissions. When the 

reader is configured for software flow control, it stops transmitting if it receives the XOFF character from 

the host (host software command 13H). It resumes transmitting only when it receives the XON character 

(host software command 11H) from the host. If software flow control is not needed, the reader should be 

configured for no flow control (

#6140 Disable Flow Control

).

Note: 

TransCore recommends that XON/XOFF software flow control be disabled while using the 

ECP.

Use the following procedure to set software flow control parameters using the terminal emulation program. 

Refer to section 

“614N Select Software Flow Control Option” on page 5–75

 .

MPRX User Guide

TransCore Proprietary

 6–96

Содержание MPRX 10-7200-001











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды