TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 28

Страница: 28 / 138

4. Disconnect the grounding RF cable from the antenna and connect the permanent RF cable to

reader.

Once the antenna is discharged and properly connected to the reader, the reader circuitry

provides a DC path to keep any further charge from building up in the antenna.

Connecting the Reader and Antenna

1.  Ensure the reader is turned off and power is disconnected.
2.  Connect one end of the RF interface cable to the antenna.
3.  Connect the other end of the RF interface cable to the appropriate antenna port on the end of the

MPRX. Refer to

Figure 10

4. The ports can be turned on in consecutive order. If all four ports will not be used, start with Port 0

and turn on connected ports. Unused ports should be set to

OFF

. Refer to

“Appendix D

Encompass 6 Options” on page D–382

for a list of commands.

Figure 10 MPRX Showing Antenna Ports

MPRX User Guide

TransCore Proprietary

2–28

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды