TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 75

Страница: 75 / 138

Disables the ECP timeout

Reader response:

#Done

Caution

Ensure that the ECP timeout is sufficient for a given baud rate. Refer to

“00 Switch to

Data Mode (Factory Default)” on page 5–58

613 Enable Data Inquiry Protocol

#613

Enable Data Inquiry Protocol. Refer to

“Data Inquiry Protocol” on page 4–44”

for more

information.

Reader response:

#Done

614N Select Software Flow Control Option

#614N

selects the Software Flow Control option for reader-to-host communications. The

factory default setting is software flow control (XON/XOFF) enabled. During data

mode and command mode operation, the following Software Flow Control options are

available. The

variable specifies Software Flow Control as shown in

Table 19

Table 19 Software Flow Control Commands

Command

Software Flow Control Option

6140

Disable software flow control

6141

Enable software flow control (factory default)

If the reader is configured for software flow control (XON/XOFF), it stops transmitting

if it receives an XOFF character (host software Command 13H). It does not resume

transmitting until it receives an XON character (host software Command 11H).

Note:

TransCore recommends that XON/XOFF Software Flow Control be

disabled while using the ECP.

6170 Disable Echo Mode

#6170

disables the reader’s echo of received host commands. If operating in basic protocol

or data inquiry protocol, the reader echoes by default. As the reader receives a host

command, it echoes each character of the command. Once the entire command has

been received and processed, the reader transmits its response. If echoing is disabled

with Command

#6170

, the reader does not echo the command, but only transmits its

response. The reader never echoes while in ECP or download mode operation.

Reader response:

#Done

6171 Enable Echo Mode (Factory Default)

6171

enables the reader to echo received host commands

#6170

disables echo mode

Reader response:

#Done

Chapter 5 Commands

TransCore Proprietary

5–75

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды