TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 138

background image

[Copyright notice]

If the failure message version number equals

0.00 E

and no serial number exists, the flash

memory checksum has failed, and the MPRX is operating out of boot ROM. In this case, the

MPRX automatically enters download mode and waits for a new program to be loaded into the

flash memory. Follow the instructions in

“Download Considerations” on page 3–40

.

Communications can also be verified by using the command sequence in

3. If a successful sign-on message is not returned, check connections and communications factors

and correct any errors.

Table 27 Command Sequence to Verify Communications

Entry

MPRX Response

Notes

#01 <CR>

#Done <CR/LF>

Switches the MPRX to command mode

#505 <CR> #Model E4 Series Ver X.XX

SN97001P <CR/LF>

Reports the software version and serial number

#00 <CR>

#Done <CR/LF>

Returns the MPRX to data mode

To check connections and communications factors

1.  Confirm that the MPRX has power.
2.  Verify the connections between the PC and the MPRX.
3.  Verify the receive (Rx) and transmit (Tx) connections.
4.  If using handshaking, verify the request to send (RTS) and clear to send (CTS) connections.
5.  Verify the COM port settings for the MPRX following the instructions in

“Serial Port Communications”

Repeat the procedures in

“Verifying Communications” on page 6–88

If you still cannot verify the MPRX and PC communications, contact TransCore Technical Support.

Chapter 6 Configuration

TransCore Proprietary

6–89

«
...
87
88
89
90
91
...
»

Содержание MPRX 10-7200-001











































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPRX 10-7200-001

Бренд: Handicare Страницы: 32

Бренд: CAME Страницы: 32

Бренд: Zepro Страницы: 52

Бренд: Panasonic Страницы: 16

Бренд: SMT Страницы: 24

Бренд: Dannmar Страницы: 85

Compute Module IO Board Plus

Бренд: Waveshare Страницы: 17

Бренд: NAIM Страницы: 31

Бренд: AMGO Hydraulics Страницы: 40

Бренд: Grundig Страницы: 24

Бренд: GeoVision Страницы: 4

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 18

MusicCast 200 TSX-N237

Бренд: Yamaha Страницы: 44

Бренд: 2VV Страницы: 19

Бренд: 2VV Страницы: 24

Бренд: Aritech Страницы: 28

Бренд: JVC Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды