TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 88

Страница: 88 / 138

Starting the Terminal Emulation Software

You can use a PC and any terminal emulation software to enter the host commands to download flash

software, configure reader operating parameters, perform diagnostics, and retrieve tag data.

To start the terminal emulation software

At the command prompt, type your terminal emulation start command and press

ENTER.

The application should display a connection description dialog box.

3. Enter a name for the session and click OK. The application should display a phone number dialog

box.

4. Choose the Com 1 option or whichever com port on the PC to which the RS–232 cable is attached.
5. Use the following values:

•

Bits per second: 9600 baud

•

Data bits: 8

•

Parity: None

•

Stop bits: 1

•

Software flow control: None

Verifying Communications

You must verify that the MPRX and the PC or laptop are communicating.

To verify communications

1. Start the terminal emulation application as described in

”Starting the Terminal Emulation Software”

on page 6–88

Note:

When testing the MPRX using a laptop computer, TransCore recommends that you configure

laptop communication parameters to match those of the host device to which the MPRX will be

connected after testing and configuration are completed.

2. Cycle the power on the MPRX. Upon startup, the MPRX transmits a sign-on message displayed on

the terminal emulation screen, or a boot ROM failure message.

The sign-on message appears as follows at a baud rate of 9600 bps:

Model [software version] SNSSSSSS [Copyright notice]

where

SSSSSS

is the serial number assigned to the MPRX skipping the fourth character printed

on the reader product label.

Serial number

000000

is the default setting and is not a valid number. If this number appears

in the sign-on message, the serial number has not been stored into reader memory. Contact

TransCore Technical Support.

If the flash memory checksum is not verifiable, the sign-on message appears as follows:

Model [E4 BOOT] Ver 0.00 A

MPRX User Guide

TransCore Proprietary

6–88

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды