TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 85

Страница: 85 / 138

#8152

send the command on Ctag pin 1 to set the Ctag address to 0.

#8153

send the command on Ctag pin 1 to set the Ctag address to 1.

MUX Operational Modes

To enable antenna multiplexing (muxing) operational modes, issue the following commands:

#836/#837

Disable/enable MPRX mode

850

RF port 0 only (factory default)

#851

mux between RF ports 0 and 1

#852

mux between RF ports 0, 1, and 2

#853

mux between RF ports 0, 1, 2, and 3

#552

Display mux setting. This display message will include “MPRX” if MPRX mode is

enabled (

#837

When MPRX mode is disabled, the reader will continuously step through each port that

has been enabled with

#85X,

stepping through whichever tag protocols are enabled

on each port, in order. The reader turning RF on will be qualified “RF on by sense”

setting. Command

#6401

is used to turn RF on continuously and bypass the RF on by

sense. Sense 0 is used for all antennas that are enabled, if RF is turned on by sense,

#641.

When MPRX mode is enabled, you must use Sense 0 and Sense 1 to turn on RF and

read tags. Sense 0, when shorted to reader signal ground, will enable tag reads on RF

ports 0 and 1 (if enabled with #851) and Sense 1 will enable tag reads on ports 2 and 3

(if enabled with #853). For example, if Commands #837 and #853 have been entered,

Sense 0 is open, Sense 1 shorted, and the reader is in data mode, the reader will

attempt tag reads toggling between RF ports 2 and 3 only. Smart muxing, ATA tag data

sniffing, and ATA dwell of two handshakes per antenna is automatic in MPRX mode.

MUX Test Modes

To enable antenna muxing test modes, issue the following commands:

#891

RF port 1 only

#892

RF port 2 only

#893

RF port 3 only

To use these test modes, MPRX mode must be disabled (

#836

) and muxing must be disabled (

#850

These command modes are not saved to NVM, and will be cleared by a power cycle of the reader, or by

enabling either MPRX mode or muxing. When these modes are enabled, the reader will continually run

through whichever tag protocols have been enabled, but only on the selected RF port. These test mode

commands are qualified by the RF on by sense settings. Use

#6401

to disable RF on by sense, if desired.

Chapter 5 Commands

TransCore Proprietary

5–85

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды