TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 77

Страница: 77 / 138

644NN Set RF Attenuation

#644NN

sets the attenuation control for the output RF power where NN is a hexidecimal value

from 00 to 0A. Settings for attenuation are 1.0 dB increments over a range of 10 dB

of attenuation from the maximum power setting of 2 watts at 0dB attenuation to a

minimum power level of 200 milliwatts at 10-dB attenuation.
The Set RF Attenuation Command NN variables and corresponding attenuation settings

are shown in

Table 21

Table 21 RF Attenuation Command Variables

Variable (NN)

Attenuation Setting (dB)

0 (factory default)

Reader response:

#Done

645NN Set SeGo Protocol Operating Range (Distance)

#645NN

sets the read range for SeGo protocol tags where NN is a hexadecimal value from 00

to 1F; the range increases with increasing NN value. The range can be adjusted for 32

discrete values where 00 is the shortest range and 1F is the longest range. The default

range value is 1F.

Reader response:

#Done

647XXX Select RF Operating Frequency

#647XXX

sets the reader RF from 860 to 930 MHz in 250-kHz steps, where

XXX

is a hexadecimal

value from 000 to 118. After the reader’s frequency is set, the value is stored in NVRAM.

This value is not altered by power-down.
If the NVRAM becomes corrupted, the correct operating frequency cannot be

guaranteed. In this circumstance, the RF section shuts down and the reader sends an

#Error06

message to the host. Until the frequency is reset using command

#647XXX

the unit displays the same error message each time it is powered up or if an attempt is

made to enable the RF by host or by external sensor.

Chapter 5 Commands

TransCore Proprietary

5–77

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды