TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 116

Страница: 116 / 138

Appendix D Command Quick Reference

Command Syntax

The command numbers consist of from 2 to 4 hex digits. The letters N or S may follow a command

number. The letter N indicates that part of the command number is variable. The letter S indicates the

requirement for an alphanumeric data string that is to be included immediately following the command

number. Hex digits (0–9, A–F) in either uppercase or lowercase characters may be used in data strings

and for hex digits A–F. For more information refer to

“Chapter 3 General Software Information” on page

3–38.
Table 36

lists factory default settings.

Table 37

lists, in numerical order, all of the commands available to

users.

Table 38

lists the same commands by command name.

Factory Default Settings

Table 36

lists the factory default settings for the MPRX.

Table 36 MPRX Default Configuration Settings

Parameter

Setting

Command

Operating mode

Data

Baud rate

9600

1005

Stop bits

1010

Parity

None

1020

Time and data appended

Enabled

302

Auxiliary information appended

Disabled

310

Unique ID code criteria

Separation of 1 ID

4100

Valid ID code criteria

Acquisition of 1 ID

4200

Uniqueness time-out

2 minutes

441

Tag translation mode

Disabled

452

Multi-tag sort

Disabled

454

SeGo protocol tag initialization

during multi-tag sort

Enabled

456

Reader ID number

6000

MPRX User Guide

TransCore Proprietary

D–116

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

TransCore MPRX 10-7200-001, Руководство пользователя, Страница: 116 / 138

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы: