TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 38

Страница: 38 / 138

Chapter 3 General Software Information

Command Entry Conventions

All MPRX commands are preceded by the start-of-message character (#). The end-of-message sequence

expected from the host is a carriage return (CR). The MPRX terminates messages with a return and a line-

feed (CR/LF). For example, the command

#01 Switch To Command Mode

is typed as follows:

#01<ENTER>

where

<ENTER>

is the Enter or Return key.

Some command characters may be represented by the letter N. This letter indicates you are to supply a

value. Maximum valid entries are the numbers 0 through 9 and the uppercase letters A through F. These

letters allow for as many as 16 available user responses and are based on the hexadecimal numbering

system.
Commands have at least two characters following the # character.

Table 10

shows the basic structure of a

four-character command.

Table 10 Four-Character Command Structure

#1005 Set Baud Rate To 9600 Baud

All commands are preceded by the # character.

Indicates the command group. This command is in Group 1 –

Communications Port Control.

Indicates the command subgroup. In this example, all commands

with a second digit of 0 apply to the main port.

The command digit. In this example, the 0 indicates that this

command affects the baud rate.

Indicates the setting. Normally this is a variable and is usually a

hexadecimal value from 0 through F. In this example, 5 sets the

baud rate to 9600, the factory setting. In some commands, this

digit may be a four-place hexadecimal string or a character string.

Command Response Conventions

Like the MPRX commands, responses are preceded by the # character. Many MPRX commands respond

with

#Done

#Error

indicating the command was or was not recognized and completed. Other

commands respond with a four-character identifier followed by one or more values.

Table 11

shows an example of a command/reply sequence. This example assumes that an MPRX with

serial number SN97001P running version X.XX software is connected to a PC running a terminal emulation

software package. The command sequence verifies that communications are working correctly.

MPRX User Guide

TransCore Proprietary

3–38

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды