TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 80

Страница: 80 / 138

Table 24 Timeout Period Values

Command

Timeout (ms)

6938

6939

693A

152

693B

300

693C

452

693D

600

693E

752

693F

Infinite (never expires,

factory default)

Reader response:

#Done

#Error.

The reader returns an Error message if a valid hexadecimal digit is not substituted for N in Command

#693N

Note:

This command only has an effect when the reader is not in MPRX mode.

694N Select Input Inversion Option

#694N

enables or disables input inversion. When inversion is enabled, an open circuit input

is interpreted as a closed circuit, and a closed circuit input is interpreted as an open

circuit. This feature allows greater flexibility in the attachment of external equipment to

the reader inputs. For example, some proximity sensors indicate presence with an open

circuit. In this instance, Command

#6941

can enable input inversion so that an open

circuit input indicates a presence. The values for N represent the two inversion options

as shown in

Table 25

Reader response:

#Done

Table 25 Input Inversion Options

Command

Option

6940

Disable input inversion (factory default)

6941

Enable input inversion

695S...S Set Serial Number (Factory Default)

695

assigns the reader serial number according to the format:

695SSSSSS

where

SSSSSS

is the serial number.

MPRX User Guide

TransCore Proprietary

5–80

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды