TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 90

Страница: 90 / 138

Verifying Tag Read Capability

After verifying communications between the MPRX and the PC, verify the capability to read tags. The test

tag should match the tag type and protocol of the tags that your system will be reading.
The polarization of the test tag must be aligned in the same direction as the antenna.

Figure 22

shows

horizontally polarized antenna and tag. The test tag must be mounted flush against a metal backplane.

Note:

Matching the tag and antenna polarization is critical to obtaining optimal system

performance.

Note:

The default tag read mode of the reader is the protocol(s) programmed into the reader. Use

only those test tags programmed with the correct protocol(s) for the reader.

Caution

To avoid damage to the MPRX, you must connect the antenna before applying power to the

reader.

To verify tag read capability

1. Once communications are verified, enter the following sequence of commands to turn on

continuous RF:

•

#01

•

#6401

•

#40

•

#00

2. Pass one test tag in front of the active MPRX antenna. If the MPRX reads the tag, the terminal

emulation application displays the tag information on the screen

Figure 22 Tag and Antenna Orientation (horizontal polarization)

MPRX User Guide

TransCore Proprietary

6–90

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды