TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 50

Страница: 50 / 138

acknowledgment message, a logical

NAK

condition is declared, and the initiator assumes the message

was received in error. In this instance, the message is retransmitted until an acknowledgment message is

received.
The message recipient, such as the host device in data mode and the MPRX in command mode, starts

a timeout counter when a

<som>

character is received. If the timeout expires without the receipt of an

<eom>

, the message acquisition is aborted (reset), and the receiver waits for the next

<som>

character.

If the message recipient receives a second

<som>

character before an

<eom>

character, the message

acquisition is aborted (reset), and retransmission of the previous message is assumed to be underway.
These strategies allow for recovery during periods when communications are marginal or lost completely.

Reader-Addressed Failure Conditions

The MPRX addresses the following failure conditions.

Illegal Sequence Number (Not in the Range 0–9, A–F)

If the MPRX detects an illegal sequence number in a host command message, it discards the received

message and sends no response. If it receives an illegal sequence number in an

ACK

message, it

responds as if a

NAK

had been received and retransmits the data.

Wrong Sequence Number

If the MPRX receives the wrong sequence number in an

ACK

message, it responds as if a

NAK

had been

received, and it retransmits the data.

Incorrect CRC

If the MPRX detects an incorrect CRC value in a host command message, it discards the received

message. No response is sent. If it receives an incorrect CRC value in an

ACK

message, it responds as if a

NAK

had been received, and it retransmits the data.

Illegal Command

If the MPRX receives an illegal command, it returns its standard

#Error

message.

Transmission Timeout

If the MPRX transmits an asynchronous message and the host does not send an

ACK

before the ECP

timeout occurs, the MPRX retransmits the message.

Receive Timeout

If the MPRX receives a

<som>

but does not receive a matching

<eom>

before the ECP timeout occurs, it

discards the incomplete message and resets its receiver.

MPRX User Guide

TransCore Proprietary

4–50

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

TransCore MPRX 10-7200-001, Руководство пользователя, Страница: 50 / 138

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы: