TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 138

background image

WARNING TO USERS IN THE UNITED STATES

FEDERAL COMMUNICATIONS COMMISSION (FCC)

LOCATION AND MONITORING SERVICE STATEMENT

47 CFR §90.351

NOTE:

The user is required to obtain a Part 90 site license from the Federal Communications

Commission (FCC) to operate this radio frequency identification (RFID) device in the United
States. The FCC ID number is

FIHMPRXV1

. Access the FCC website at

www.fcc.gov

to obtain

additional information concerning licensing requirements.

NOTE:

Users in all countries should check with the appropriate local authorities for licensing

requirements.

FCC RADIO FREQUENCY INTERFERENCE STATEMENT

47 CFR §15.105(A)

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate RF energy and may cause
harmful interference to radio communications if not installed and used in accordance with the
instruction manual. Operating this equipment in a residential area is likely to cause harmful
interference, in which case, depending on the laws in effect, the user may be required to
correct the interference at their own expense.

NO UNAUTHORIZED MODIFICATIONS

47 CFR §15.21

CAUTION:

This equipment may not be modified, altered, or changed in any way without permission.

Unauthorized modification may void the equipment authorization from the FCC and will void
the warranty.

USE OF SHIELDED CABLES AND GROUNDING

47 CFR §15.27(A)

NOTE

: Shielded cables and earth grounding the unit is recommended for this equipment to

comply with FCC regulations.

TRANSCORE, LP

USA

TransCore Proprietary

iii

«
1
2
3
4
5
...
»

Содержание MPRX 10-7200-001











































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPRX 10-7200-001

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: M-system Страницы: 10

Бренд: Dickey-John Страницы: 109

Xenta 400 Series

Бренд: TAC Страницы: 48

CompuScope 85GC

Бренд: Gage Страницы: 174

Бренд: Daewoo Страницы: 44

Бренд: Automated Logic Страницы: 3

Бренд: BHM Medical Страницы: 56

Бренд: M-system Страницы: 7

Бренд: Idemia Страницы: 74

Бренд: Stahl Страницы: 24

AQUACIAT POWER LD 602R-3500R

Бренд: CIAT Страницы: 56

SmartStuff SmartBox

Бренд: TCP Страницы: 2

Over-Center 7k51

Бренд: Basta Boatlifts Страницы: 16

Бренд: MSW Страницы: 7

Бренд: Riello Страницы: 20

Бренд: Sunrise Medical Страницы: 36

Бренд: Len Gordon Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды