TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 68

Страница: 68 / 138

odd parity

00 ms end-of-line delay (fixed)

One space is required between each value. For example, if factory default settings are assigned, the

reader message is

MAIN B5 S0 P0 D0

indicating 9600 baud, one stop bit, no parity, and 0-ms end-of-line delay.

Note:

The information transmitted in response to Command

#522

applies to data and command

mode operation only. While operating in download mode, default communications parameters are

always used.

524 Display Appended Information Status

#524

displays the information being appended to the reader transmissions. Command

#31N

appends information.

Reader response:

IDAP T<0 to 1> D<0 to 1> X<0 to 1>

where

Time not appended

Time appended

Date not appended

Date appended

Auxiliary information not appended (factory default)

Auxiliary information appended
One space is required between each value. For example, if factory-default settings are

assigned, the reader response is

IDAP T1 D1 X0

indicating time and date appended, and auxiliary information not appended.

525 Display Communications Protocol Status

#525

displays the status of Command

#610

Select Basic Communications Protocol,

Command

#611

Select Error Correcting Protocol, or

#613

Enable Data Inquiry

Protocol, Command

#614N

Selected Mode of Software Flow Control

and Command

#612NN

Error Correcting Protocol Timeout

Reader response:

ECPS P<0 to 2> T<01 to FF> X<0 to 2> S0

where

Basic protocol selected (factory default)

ECP enabled

data inquiry protocol enabled

Txx

ECP timeout where

= 01 to FE (hexadecimal) |

Timeout (ms) = 50 * xx

If xx = FF timeout disabled

MPRX User Guide

TransCore Proprietary

5–68

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды