TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 18

Страница: 18 / 138

MPRX User Guide

TransCore Proprietary

1–18

Reader

The MPRX consists of an input/output (I/O) module, a power supply, a reader logic board (also called a tag

decoder), and a radio frequency (RF) transmitter/ receiver (called the RF module) in a compact enclosure.

These components are contained in a highly reliable, compact, and easy-to-install package.

Figure 1

shows the four port version of the MPRX. The host connector, sense connector, Ethernet connector, and

interface selection switch are on the opposite end of the MPRX from the four antenna port locations.

Power and Communications Cables

Cable length for power and communications depends on the physical characteristics of the MPRX

installation site.

Table 1

lists accessory kits available for cabling options based on your site’s requirements.

Table 1 Connector Cabling Accessory Kits

Part Number

Description

58-7200-001

MPRX host connector leads 0.15m (6in)

58-7200-002

MPRX host cable assembly 3m (120in)

58-7200-003

MPRX host cable assembly 5m (200in)

58-7200-004

MPRX host cable assembly 10m (400in)

58-7201-001

MPRX sense connector leads 0.15m (6in)

58-7201-002

MPRX sense cable assembly 3m (120in)

58-7201-003

MPRX sense cable assembly 5m (200in)

58-7201-004

MPRX sense cable assembly 10m (400in)

Figure 1 MPRX End Views

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

TransCore MPRX 10-7200-001, Руководство пользователя, Страница: 18 / 138

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы: