TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 81

Страница: 81 / 138

The serial number may contain as many as six uppercase or lowercase ASCII

alphanumeric characters.

Note:

The factory-assigned serial number of the reader contains seven characters. However, to

maintain backward compatibility, the reader software allows only six characters to be entered.

When setting the serial number, skip the fourth (middle) character of the seven-character number

shown on the reader product label.

Note:

Once assigned, the serial number is preserved during power-down and the loading of default

parameters.

Reader response:

Done

696S...S Store Hardware Configuration String (Factory Default)

#696S...S

stores hardware configuration information into reader memory. The hardware

configuration string is assigned according to the following format:

696S...S

where

S...S

is the hardware configuration string that may contain as many as 20 uppercase or

lowercase ASCII alphanumeric characters.

Note:

Once assigned, configuration information is preserved during power-down and the loading of

default parameters.

Reader response:

#Done

697 Set User-Programmable Group Select Equals (GSE) Filter

#697

sets the user-programmable GSE filter. The command string is assigned according to

the following format:

697 MM AA DDDDDDDDDDDDDDDD

where

MM =

The tag uses this mask to determine which of the eight Comparison Data bytes are to

be compared for the Group Select filter.

This field is used by the tag to determine the start address in the tag memory for the

comparison data.

DD…DD =

Comparison Data: an 8-byte field (16 characters) used by the tag as the comparison

data for the Group Select filter. The tag compares the data in this field to data in tag

memory beginning at the Start Address to determine if the tag will respond to a reader

Group Select request. Only the bytes having the corresponding bit set in the GSE Mask

is used for this comparison.
As an example, to configure a reader to have only tags with data in byte locations 10, 12,

and 15 (decimal) with hexadecimal values “00,” “01,” and “02,” the following command is

used:

#697 A4 0A 0005014202024133

Chapter 5 Commands

TransCore Proprietary

5–81

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды