TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 65

Страница: 65 / 138

#443

30 seconds

Entering these commands effectively expires the timeout clock, which erases all current IDs in the

comparison register. In effect, the first ID that is acquired after the clock expires always appears to be new

and is stored. Newly acquired IDs are only tested against IDs that are registered after the clock resets.
The timeout clock is continually reset (does not expire) as long as the reader receives the same tag ID. For

example, assume that the timeout clock is set for two minutes and there is a railcar parked on a siding in

front of the reader. Without this reset feature, the railcar’s ID would be reported every two minutes (each

time the timeout clock expired).

452 Disable Tag Translation Mode (Factory Default)

#452

disables tag translation mode. Incoming full-frame tags will be converted directly to

ASCII. They will not be translated from Association of American Railroads (AAR) and

American Trucking Associations (ATA) format to ASCII.

Reader response:

#Done

453 Enable Tag Translation Mode

#453

enables the translation of tags in AAR and ATA formats. Specific data fields, such as

owner ID and car number, will be extracted from these tags, translated according to

AAR or ATA standards, and converted to ASCII. Tags that are not programmed in AAR or

ATA format will be converted directly to ASCII. The reader will not attempt to translate

data from half-frame or dual-frame tags.

Reader response:

#Done

454 Disable Multi-tag Sort (Factory Default)

#454

Disables the multi-tag sort function.

Reader response:

#Done

455 Enable Multi-tag Sort

#455

enables the multi-tag sort function that allows the reader to identify unique tags within a

group.

Reader response:

#Done

Note:

Enabling the multi-tag sort function adversely affects the vehicle speed at which tags may be

read. If there is only one tag expected in the vehicles of the target population, multi-tag sort should

be disabled.

456 Enable SeGo Protocol Tag Initialization During Multi-tag Sort (Factory

Default)

#456

enables the reader to send the Super eGo® (SeGo) protocol tag initialize command

as part of the multi-tag sort function. When the reader sends the SeGo protocol tag

initialize command, all tags in the RF field reenter the sort process.

Reader response:

#Done

Chapter 5 Commands

TransCore Proprietary

5–65

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды