TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 78

Страница: 78 / 138

Note:

The authorized continuous wave (CW) frequency band for the MPRX in the U.S. is 902.25 to

903.75 MHz and 910.00 to 921.50 MHz and the authorized modulated frequency band for the MPRX

in the U.S. is 911.75 to 919.75 MHz. The RF for each MPRX at the site must be set according to the

frequency specified in the FCC site license. Only trained, authorized installation and maintenance

personnel are permitted by FCC to set the RF.

Refer

“Table 27 Command Sequence to Verify Communications” on page 6–89

“Table 40 RF

Frequency Commands Non- FCC” on page D–133

for a list of commands.

Reader response:

#Done

65 Reset Power Fail Bit

#65

resets the power fail bit to 0. The bit changes from 0 to 1 when power is restored to

the reader. Upon reader power-up, the host transmits either Command

#65

#63

Reset Reader to properly initialize this bit. The current state of the power fail bit may be

displayed. Refer to

“520 Display Power Fail Bit” on page 5–67

for more information.

Reader response:

#Done

66F Load Default Operating Parameters

#66F

loads all the factory default operating parameters except RF operating frequency. Refer

“Table 26 MPRX Default Configuration Settings” on page 6–86

for a listing of the

defaults.

Reader response:

#Done

All parameters loaded OK

#Error

A parameter load failed

690N Select Presence Without Tag Report Option

#690N

enables or disables the presence without tag report option. If the presence without tag

reporting option is enabled using Command

#6901

, input

reports are transmitted when

a tag presence is detected without the subsequent acquisition of a valid tag. The value

for

specifies the reports as shown in

Table 22

Table 22 Presence Without Tag Report Commands

Command

Report Option

6900

Disable presence without tag reports (factory default)

6901

Enable presence without tag reports

Note:

These commands only have an effect when the reader is not in MPRX mode.

Reader response:

#Done

Refer to

“Basic Protocol and ECP Format” on page 4–44

for message format information.

MPRX User Guide

TransCore Proprietary

5–78

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды