TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 67

Страница: 67 / 138

506 Display Hardware Configuration Information

#506

displays hardware configuration information stored in the reader memory by the user.

Hardware configuration information is empty by default until you set the information to

any 20 character ASCII string desired using Command #696S...S.

Reader response: An ASCII string from 1 to 20 characters in length

520 Display Power Fail Bit

#520

displays the value of the reader power fail bit. The power fail bit changes from 0 to 1

when power to the reader is interrupted. To reset the bit, use Command

#63

Reset

Reader or Command

#65

Reset Power Fail Bit. On initial power-up, the host should

transmit one of these two commands to clear the power fail bit.

Reader response:

PWRB P<0 to 1> R0

where

No power failure detected

Power failure detected

Not applicable to the MPRX

521 Display Reader ID Number

#521

displays the reader ID that is sent in the auxiliary data field.

Reader response:

RDID xx

where

01 to FF (hexadecimal)

522 Display Communications port Parameters

Command

#522

displays the selected communications port parameters, including the baud rate (

#100N

the number of stop bits (

#101N

), the parity scheme (

#102N

), and the end-of-line delay.

Reader response:

MAIN B<2 to 7> S<0 to 1> P<0 to 2> D0

where

1200 baud

2400 baud

4800 baud

9600 baud (factory default)

19.2 kbps

38.4 kbps

one stop bit (factory default)

two stop bits

no parity (factory default)

even parity

Chapter 5 Commands

TransCore Proprietary

5–67

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды