TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 63

Страница: 63 / 138

current status of input0 and input1 (0 to 3)

sss

relative to tag read strength

Reader response:

#Done

ID Filtering — Command Group 4

Group 4 commands set criteria for filtering (buffering or discarding) ID codes. These commands are useful

for eliminating duplicate ID codes and selecting the type of tags read by the MPRX.

40 Transmit All ID Codes

#40

instructs the reader to transmit all IDs without regard for uniqueness. This command

can be useful when tuning the read zone and mapping the footprint or performing

diagnostics.
After diagnostics are complete, you may want to reinstate the uniqueness check using
Command

#410N

Select Unique ID Code Criteria

Reader response:

#Done

410N Select Unique ID Code Criteria (Anti-passback Feature)

#410N

instructs the reader to buffer and transmit ID codes according to the following test: an

ID is read if previously decoded IDs have changed value at least

N+1

times since the

new ID was last received. IDs that do not pass the test are not reported. The factory-

default setting is Command

#4100

, which selects a separation of one ID. Variable

specifies ID separation as shown in

Table 17

Table 17 Unique ID Code Criteria

Command

Uniqueness Criteria

4100

Separation of 1 ID (factory default)

4101

Separation of 2 IDs

4102

Separation of 3 IDs

4103

Separation of 4 IDs

Each time the reader receives a tag ID, it compares the ID with the contents of a

comparison register. This register contains the following two items:

Item 1

Most recently acquired ID

Item 2

Second-most recently acquired ID

Item 3

Third-most recently acquired ID

Item 4

Fourth-most recently acquired ID
When the uniqueness filter is set to separation of one ID, the newly acquired ID

is transmitted only if it is different from the first item. Separation of two IDs allows

transmission if the new ID is different from Items 1 and 2 in the comparison register.

Chapter 5 Commands

TransCore Proprietary

5–63

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды