Tieline Genie Distribution Скачать руководство пользователя страница 220 | Manualshive

Страница: 220 / 426

Tieline Genie Distribution Скачать руководство пользователя страница 220

220

Genie Distribution WNET Manual v3

© Tieline Research Pty. Ltd. 2020

Important Notes on G3 Profile Settings:

The G3 profile setting supports maintaining specific G3 codec settings when answering a
call from a G5 codec.

1.

Auto

: The codec will dial the G3 codec and connect in mono or stereo. Note: This

is overridden in a ViA codec when a G3 Main + IFB use-case is configured.

2.

Dual Program

: This allows the codec to dial a G3 codec with a Dual Program

profile loaded and support two simultaneous mono connections. Note: When
connecting in dual mono (2 x Mono Peer-to-Peer) mode to a G3 codec over IP both
audio streams must encode using the same algorithm and sample rate or the G3
codec will not connect.

3.

Runtime

: The G3 codec will retain runtime settings when answering a call from a

G5 codec.

4.

Custom

: The G3 codec will load a specified profile, e.g. profile 6, which is the first

custom profile number.

Important Notes on G3 Channel Settings

:

This setting is for compatibility with the

Dual Mono

profile in Tieline Commander G3 and

i-Mix G3 codecs. It is designed to configure routing of the audio stream to a specific G3
codec channel consistently.

1.

Auto

(default): The answering codec will route incoming calls on a first come first

served basis.

2.

Channel 1

: The answering codec will always route incoming calls to codec

Channel 1

(left output).

3.

Channel 2

: The answering codec will always route incoming calls to codec

Channel 2

(right output).

5. This audio stream connection in the wizard will configure the codec to connect the first audio

stream. Enter the name of the connection in the text box, then click

Next

.

6. Configure the transport settings for the connection, then click Next. Note: Select

Enable

Auxiliary Data

to enable synchronized out-of-band data in separate packets using any

algorithm.

Important Note:

See

RS232 Data Configuration

for detailed information on RS232 data

and see

Enabling Relays and RS232 Data

for more information on relay operations.

7. Configure destination codec dialing and encoding settings:

«
...
218
219
220
221
222
...
»

Содержание Genie Distribution











































































































































































































































































































































































































































Отзывы:

Нет отзывов