Teseq NSG 3040 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 156

background image

145

Technical specifications

Max. peak. current

5000 Amp

Max. RMS current:

>63 Amp

Nominal ratio:

500:1 (into 1 MΩ system)

1000:1 (into 50 Ω system)

Sensitivity:

0.002 V/Amp (MΩ system)

0.001 V/Amp (Ω system)

Hole diameter:

8 mm

Probe connector:

SMA

Scope coax cable:

with SMA and BNC connectors

Operating temperature:

0 to 55°C

Output impedance:

50 Ω

Accuracy:

<±2%

MD 300 set:

Carry case, current probe, coax cable

with SMA/BNC connector, shorting

cable with safety banana connectors,

calibration certificate, user manual

Options

INA 6560:

FISCHER to banana plug adaptor set

INA 2042:

LEMO to banana plug adaptor set

INA 6554:

IEC 320 single phase to safety banana

adaptor leads 2 x 155-131 6 to 4 mm

adaptors with safety banana

connectors

Note: The carry case provides spare place for all options

The probe can be used for current pulse verification on surge generators.
Optional FISCHER or LEMO connectors are available for matching the safety
banana connectors of the shorting cable to the HV output of the generator.
For monitoring the EUT current during a test, an additional IEC adaptor with the
safety banana connectors can be connected to the generator EUT output for
observation of one lead at a time.

«
...
143
144
145
146
147
...
»

Содержание NSG 3040





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для NSG 3040

Бренд: QFX Страницы: 44

Бренд: Cambridge Audio Страницы: 4

Бренд: Cambridge Audio Страницы: 2

blueplanet 15.0 TL3

Бренд: Kaco Страницы: 188

Бренд: Kaiser Baas Страницы: 3

Бренд: Saftronics Страницы: 62

SOLIVIA 2.5 AP G3 TR

Бренд: Delta Страницы: 48

Бренд: OXO Страницы: 20

Бренд: Roland Страницы: 6

Бренд: B&B Electronics Страницы: 3

Бренд: KAMEHA Страницы: 12

Бренд: Lechpol Страницы: 2

Бренд: Senci Страницы: 39

Бренд: National Communications Страницы: 20

Бренд: Actox Страницы: 36

SinePower MSI212

Бренд: Waeco Страницы: 220

Бренд: Morningstar Страницы: 16

Бренд: Tripp Lite Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды