Teseq NSG 3040 Скачать руководство пользователя страница 44

Страница: 44 / 156

NSG 3040 EMC test system

To open the NSG 3040, the user must first remove the sides panels. Each side
panel has 4 snap fixtures which will separate when outward pressure is applied.

1. Pull outward on the indentation in the front of the side panel. A blunt tool

which will not scratch the paint on the panel may be used.

2. Pull outward to separate the panel from the snap fixtures.

3. Remove the upper screws on both sides of the generator cover.

4. Remove the NSG 3040 cover. The SD-card slot is located at the right front of

the generator, in back of the front panel.

5. Press the SD-card to release it. Remove the card from the slot. To install a

new SD-card, proceed to step 7.

6. To download new software from a PC to the SD card, insert the card in the

SD port of the PC and copy the software to the SD card. The file name must
remain SUI3000AP.EXE. Remove the SD card from the PC.

7. Insert the SD-card in the NSG 3040. Follow steps 1 - 4 in reverse to replace

the generator cover and side panels.

8. Restart the NSG 3040. The new software version will boot automatically and

may be verified in the equipment detail window (see section 7.7.1).

Содержание NSG 3040





























































































































































Результаты поиска

Содержание NSG 3040

Отзывы:

Похожие инструкции для NSG 3040

Бренды по названию

Популярные бренды

Teseq NSG 3040, Руководство пользователя

Результаты поиска

Содержание NSG 3040

Отзывы:

Похожие инструкции для NSG 3040

Бренды по названию

Популярные бренды