Siemens LMV50 series Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 327

background image

72/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

4.2.5 Auxiliary functions

4.2.5.1 Hours run counter

The LMV5 has an hour’s run counter for gas-fired and oil-fired operation.
The counters start from safety time 1 (phase 40) and are stopped at the end of
operation (when leaving the 6X phases).

The following counters are available and can be displayed using the AZL52 in the

Operation / HoursRun

menu; some of the settings can also be adjusted:

Parameter GasFiring

Operating hours for gas (adjustable)

OilStage1/Mod

Operating hours for oil stage 1 or modulating
(adjustable)

OilStage2

Operating hours for oil stage 2 (adjustable)

OilStage3

Operating hours for oil stage 3 (adjustable)

TotalHoursReset

Total operating hours (resettable)

TotalHours

Total operating hours (read only)

SystemOnPower

Operating hours when system is connected to
power (read only)

4.2.5.2 Start counter / startup counter

The LMV5 records the number of starts / startups and saves these permanently (via
mains voltage OFF).
The relevant start counters count up with each burner startup cycle (phase 20). This
also occurs if startup is subsequently aborted.

The following counters are available and can be displayed using the AZL52 in the

Operation / StartCounter

menu; some of the settings can also be adjusted:

Parameter GasStartCount

Number of startups for gas, start counter
(adjustable)

OilStartCount

Number of startups for oil, start counter
(adjustable)

TotalStartCountR

Total no. of startups, start counter (resettable)

TotalStartCount

Total no. of startups, start counter (read only)

4.2.5.3 End of life cycle function

The end of the life cycle of the LMV5 (switching cycles of the relays) is detected and
displayed on the AZL52.
The end of the life cycle is reached when the total startup counter

TotalStartCount

has

reached 250,000 starts.

This leads to the following message on the AZL52:

Startups > 250,000 maintenance

This means that the LMV5 has to be replaced, refer to chapter

Life cycle

.

This message can be hidden manually by pressing ESC.
If the message has been hidden, it will automatically appear again after an additional
10,000 starts.
Error and start prevention messages have priority over the end of lifecycle message.

4.2.5.4 Fuel meter

Refer to chapter

VSD module

.

«
...
70
71
72
73
74
...
»

Содержание LMV50 series








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LMV50 series

Бренд: Keithley Страницы: 59

Бренд: National Instruments Страницы: 17

Бренд: Salus Страницы: 16

Бренд: Cypress Semiconductor Страницы: 9

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

Бренд: Avenview Страницы: 28

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: AXIOMTEK Страницы: 2

Бренд: ADS Technologies Страницы: 1

Бренд: CSL Страницы: 24

Бренд: Altimium Страницы: 12

CloudGen Firewall

Бренд: Barracuda Страницы: 8

SecPath F50X0 Series

Бренд: H3C Страницы: 41

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

Бренд: NUROTRON Страницы: 16

Lexicon MPX 200

Бренд: Harman Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды