Siemens LMV50 series Скачать руководство пользователя страница 297 | Manualshive

Страница: 297 / 327

Siemens LMV50 series Скачать руководство пользователя страница 297

297/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

20 Flue gas recirculation (FGR) function (LMV50/LMV51.3/LMV52)

22.05.2018

20.3.2 Settings in temperature-compensated mode (only

LMV52.4)

Β

Note!
Recommendation:
First, make the initial settings with no influence from flue gas recirculation (FGR).

This enables the fuel-air ratio control system to be set as if the plant operated without
flue gas recirculation (FGR).

For that purpose, set flue gas recirculation (FGR) mode

temp.comp.

or

TCautoDeact

to

deactMinpos

.

This way, auxiliary actuator 3 is always maintained at the minimum position of flue gas
recirculation (FGR).

After completing the settings of the fuel-air ratio control curves without flue gas
recirculation (FGR), the actual settings with an active auxiliary actuator 3 can now be
made.

When setting the fuel-air ratio control curves of auxiliary actuator 3 in flue gas
recirculation (FGR) mode

temp-compensated,

the current flue gas recirculation (FGR)

temperature is also displayed.

Select the required curvepoint, then continue by pressing

Enter

.

⇒

P

o

i

n

t

|

P

o

i

n

t

:

3

|

c

h

a

n

g

e

?

O

2

|

d

e

l

e

t

e

?

2

.

8

I

Here, the cursor position can be changed between

change

and

delete

.

The edit a curvepoint, select

change

.

- Continue by pressing

Enter

⇒

Selection whether the actuators shall follow the adjustment.

Caution!
Temperature-compensated flue gas recirculation (FGR) can be correctly set only
when selecting with

DriveLowfire

in operation!

A change in the curve point without the corresponding flue gas recirculation
temperature (e.g.

without driving

in operation or in standby) results in an

incorrect

pairing

of the values

Flue gas recirculation position

and

Flue gas

recirculation temperature

.

This can lead to excessive amounts of recirculated flue gas, which might cause
the flame to lift: Stability limit of flame.

«
...
295
296
297
298
299
...
»

Содержание LMV50 series








































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды