Siemens LMV50 series Скачать руководство пользователя страница 70

Страница: 70 / 327

70/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

4 Burner control

22.05.2018

4.2.3.14 Startup sequence stop in phase 36

The burner's startup sequence can be stopped in phase 36 via input X5-03 pin 3 if
parameter

Config X5-03

has been set to

DeaO2/Stp36

The stop takes place if

mains voltage is present.

Attention!
This function may only be used for

non-safety-related

multiple burner

applications.

Note!
At the same time as this parameter setting, input X5-03 pin 2 is set

to deactivation of

O2 trim control

(

DeaO2/Stp36)

This function cannot be used if the inputs (X5-03 pin 2 / pin 3) are being used to
connect an external load controller
(LC_OptgMode = ExtLC X5-03)

↑

invalid parameter setting.

Parameter Config X5-03 (DeaO2/Stp36)

4.2.3.15 Cooling function in standby mode (only LMV50)

In order to cool the burner in standby mode, a cooling function can be activated using
parameters.

The cooling function is started with a mains voltage signal at input X5-03 pin 3:

∂

The fan is switched on and supervised in the same way as for

continuous purging

∂

The actuators used for determining the amount of air are driven to their postpurge

positions

∂

If no mains voltage signal is present, the device behaves as for

without continuous

purging

in standby mode

Parameter Config X5-03 (CoolFctStby)

Attention!
This function may only be used for

non-safety-related

multiple burner applications.
This means, for example, that the function may not be used for safety-related
purging in plants with several burners in one combustion chamber.

Note!

∂

This function cannot be used if the inputs (X5-03 pin 2 / pin 3) are being used to

connect an external load controller (LC_OptgMode = ExtLC X5-03)

↑

invalid

parameter setting

∂

When using the cooling function, the

ContinuousPurge

parameter must not be set

off Sloop

deac/VSD-SL

as these settings cancel each other out, potentially

resulting in error messages

4.2.3.16 Long postpurge time (only LMV50 / LMV52.4)

If a long postpurge time is required, an additional time can be set in one-minute
intervals via an additional,

non

fuel-specific parameter

PostpurgeT3long.

This time is added to the two fuel-specific times

PostpurgeT3Gas / Oil

Parameter PostpurgeT3long

Содержание LMV50 series








































































































































































































































































































































Результаты поиска

Содержание LMV50 series

Отзывы:

Похожие инструкции для LMV50 series

Бренды по названию

Популярные бренды

Siemens LMV50 series, Руководство пользователя

Результаты поиска

Содержание LMV50 series

Отзывы:

Похожие инструкции для LMV50 series

Бренды по названию

Популярные бренды