Siemens LMV50 series Скачать руководство пользователя страница 112

Страница: 112 / 327

112/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

7 Boiler controller / load controller

22.05.2018

Manual operation,

shutdown or standby

Manual operation,

startup or operation

Automatic operation,

shutdown or standby

Automatic operation,

startup or operation

Change to automatic operation

Startup

Burner ON, low-fire

Burner OFF

Burner ON, low-fire

Waiting until actual value < setpoint minus 5 %

Setting phase of controlled system, fixed at 5 min

Evaluation of development of actual value. If actual value changes excessively,

setting phase will be extended by another 5 min max

Startup

Saving the startup values and output of the parameterized adaption load

When the temperature or pressure increase changes to a straight line, the delay time Tu

and the maximum increase of the controlled system is ascertained from the measured

values and the start values. These values are then used to calculate the control parameters.

If the adaption load is below 100 %, a correction factor will be used.

Adaption will be terminated or stopped:

before

the

setpoint

reached

- in the case of unusual developments of the actual value (e.g. pure dead time member

with

extensive

dead

time)

End of adaption is communicated to the AZL... . If adaption was correct, the control parameters

will be saved in EEPROM. Otherwise, the former control parameters are reinstaled and the

change to modulating control will take place.

Note:

If adaption was successful, the former control parameters in EEPROM will be overwritten.

The control then uses the new parameters without waiting for an extra confirmation by the

user. The new control parameters appear on the AZL... and are valid from now on.

Burner OFF

7550f21E/0 502

Figure 55: Modulating control – adaption sequence

Note!
Refer to chapter

Displays and settings / special function adaption load controller

Adaption sequence

Содержание LMV50 series








































































































































































































































































































































Результаты поиска

Содержание LMV50 series

Отзывы:

Похожие инструкции для LMV50 series

Бренды по названию

Популярные бренды

Siemens LMV50 series, Руководство пользователя

Результаты поиска

Содержание LMV50 series

Отзывы:

Похожие инструкции для LMV50 series

Бренды по названию

Популярные бренды