Siemens LMV50 series Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 327

Siemens LMV50 series Скачать руководство пользователя страница 106

106/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

7 Boiler controller / load controller

22.05.2018

BACS for control with digital predefined load via bus.
The LMV5 is connected to a BACS via the AZL5 and an external bus interface (e.g.
Modbus).
The BACS contains the controller and transmits the load (manipulated variable) and the
heat request to the LMV5.
In this operating mode, the load controller inside the LMV5 is not required.

AZL5...

CAN module

(basic unit)

FARC (BU)

Demand

for heat

BC (BU)

Manipulated variable,

demand for heat

Manipulated variable,

demand for heat

CAN bus

7

5

50

b

0

6e

/0

7

0

4

Internal

load controller

Manipulated

variable

0...100 %

Modbus /

e-bus

BMS

Ja

ck

X

72

-Predefined output
-Demand for heat

Figure 52: Operating mode 6 with load controller

7.3.1 Manual / automatic burner startup

Parameter

Autom/Manual/Off (Automatic/ Manual / Burner off)

Parameter

SetLoad (0…100% / S1 / S2 / S3)

Parameter

Autom / Manual / Off

is used to define whether the burner is operated

manually or automatically (controller mode).

Burner off

The LMV5 remains in or goes into standby mode, irrespective of
whether the boiler controller demands heat or not. An error message is
not displayed.

Manual

The burner is switched on provided that the controller release is present
at terminal X5-03 pin 1 and the start release for the respective fuel
occurs in phase 21 at the terminal (X6-01 / X7-03).
The burner output can then be set using the

SetLoad

parameter and

must lie within the burner's working range.

Automatic

The burner start for the respective fuel (which is present at terminal (X6-
01 / X7-03)) depends on heat demand of controller (X5-03 pin 1) and of
start release (phase 21).

With remote control, parameter

Autom / Manual / Off

can only be accessed by reading.

Parameter

SetLoad –

by contrast – can be read and written.

Operating mode 6
(Ext LC bus)

«
...
104
105
106
107
108
...
»

Содержание LMV50 series








































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды