manualshive.com logo in svg

Siemens LMV50 series, Руководство пользователя

Поделиться
Скачать
Siemens LMV50 series Скачать руководство пользователя страница 115

115/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

7 Boiler controller / load controller

22.05.2018

7.4.3  Multistage control

When selecting

Oil

, the LMV5 must be set to

2-stage

 or

3-stage

, depending on the type

of burner, using parameter

Operation Mode (

refer to chapter

 Control characteristics)

.

In these 2 operation modes, the PID algorithm is not required and is not calculated.
Maximum 3 fuel stages are activated and deactivated depending on the actual values,
the parameterized switching differentials_Stage1...3

(

r

efer to chapter

 Integrated 2-

position controller (R = ON/OFF)

), and the parameterized reaction thresholds

Q2

 and

Q3

.

This approach is used to reduce the switching frequency of the higher stages.

∂

  The integral of the control deviation over time is generated

∂

  Switching on of stage 2 is locked until the temperature has dropped below the

adjustable reaction threshold

Q2

∂

  Switching on of stage 3 is locked until the temperature has dropped below the

adjustable reaction threshold

Q3

If the temperature frequently drops below the switch-on thresholds, the integrals are
added up and the higher stage switched on when the associated Q-value is reached.
If, before that, the setpoint is reached with the lower stage, the counter is reset.

Parameter  ThreshStage2On 

(Q2)

ThreshStage3On (Q3)

Reaction thresholds

Q2

 and

Q3

 (integral of control deviation (K) x time (s))

General

Load-dependent
activation of the
higher burner stages

Содержание LMV50 series








































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды