Siemens LMV50 series Скачать руководство пользователя страница 177

Страница: 177 / 327

177/327

Building Technologies

Basic Documentation LMV5...

CC1P7550en

9 Commissioning instructions for the LMV5

22.05.2018

For the parameters

HomePos

Prepurge position

and

Postpurge position

, the parameter

set supplied offers presettings. These should be checked and, if necessary, adapted,
either now or during the following program stops.
There is

presetting for the ignition position. In this section, a valid setting must be

made because otherwise, the burner cannot be started up.

Menu level 1

Menu level 2

Menu level 3

Menu level 4

Menu level 5

Menu level 6

Params & Display

RatioControl

OilSettings

SpecialPositions

IgnitionPos

IgnitionPosOil
IgnitionPosAir
IgnitionPosAux1
IgnitionPosAux2

Only LMV52

IgnitionPosAux3
IgnitionPosVSD

LMV50/LMV51.3/
LMV52

Example:

Auxiliary actuator: 22.5° Air actuator: 37.6°

These values are also transferred to operating point S1 even if it has not yet been set.

To start the burner, select

Autom/Manual/Off,

and then

Manual

Menu level 1

Menu level 2

Menu level 3

Menu level 4

Menu level 5

Menu level 6

ManualOperation

Autom/Manual/Off

If startup shall be watched, the display can be changed to

Normal operation

pressing simultaneously selection buttons «

» and «

».

The burner control stops startup in the prepurge phase (phase 24), enabling the
positions of the actuators for prepurging to be straightforwardly set.

Menu level 1

Menu level 2

Menu level 3

Menu level 4

Menu level 5

Menu level 6

Params & Display

RatioControl

OilSettings

SpecialPositions

PrepurgePos

PrepurgePosAir
PrepurgePosAux1
PrepurgePosAux2

only LMV52

PrepurgePosAux3
PrepurgePosVSD

LMV50/LMV51.3/
LMV52

Note!
The prepurge position of auxiliary actuator 3 is approached in phase 32 (flue gas
recirculation (FGR)).

After the settings are made, the program stop in the prepurge position should be
replaced by the program stop of the ignition position in phase 36.

21. Checking and
presetting the ignition
positions for firing on oil

22. Manual startup

23. Actuator positions
during the prepurge time

Содержание LMV50 series








































































































































































































































































































































Результаты поиска

Содержание LMV50 series

Отзывы:

Похожие инструкции для LMV50 series

Бренды по названию

Популярные бренды

Siemens LMV50 series, Руководство пользователя

Результаты поиска

Содержание LMV50 series

Отзывы:

Похожие инструкции для LMV50 series

Бренды по названию

Популярные бренды