Siemens 6RA7013-6DV62, Руководство по эксплуатации, Страница: 677 / 734

05.05 Connectors and binectors
SIEMENS AG 6RX1700-0AD76
12-29
SIMOREG DC Master Operating Instructions
Binector Name, description Function
diag., Sheet
B0143
Stat.word 2, bit 21 inverted
G183
B0144
Stat.word 2, bit 22: 0=no overload alarm active, 1=overload alarm active
G183
B0145
Stat.word 2, bit 22 inverted
G183
B0146 Stat.word 2, bit 23: 0=no overtemperature fault active, 1=overtemperature fault active
G183
B0147 Stat.word 2, bit 23 inverted
G183
B0148 Stat.word 2, bit 24: 0=no overtemperature alarm active, 1=overtemperature alarm active
G183
B0149 Stat.word 2, bit 24 inverted
G183
B0150 Stat.word 2, bit 25: 0=no motor overtemperature alarm active, 1=motor overtemperature alarm active
G183
B0151 Stat.word 2, bit 25 inverted
G183
B0152 Stat.word 2, bit 26: 0=no motor overtemperature fault active, 1=motor overtemperature fault active
G183
B0153 Stat.word 2, bit 26 inverted
G183
B0156 Stat.word 2, bit 28: 0=no motor blocked fault active, 1=motor blocked fault active
G183
B0157 Stat.word 2, bit 28 inverted
G183
Messages
B0160 0=AUS1 or AUS3 active, 1=no AUS1 and no AUS3 is pending
G180
B0161 B0160 inverted
G180
B0164 1 = n < n
min
[SW 1.4 and later]
G187
B0165 B0164 inverted [SW 1.4 and later]
G187
B0166 1 = Voltage at power section is active [SW 1.4 and later]
B0167 B0166 inverted [SW 1.4 and later]
B0168 1 = E-Stop is active [SW 1.4 and later]
G117
B0169 B0168 inverted [SW 1.4 and later]
G117
B0172 Output of "Setpoint-actual value deviation 2" signal [SW 1.9 and later] G187
B0173 B0172 inverted [SW 1.9 and later] G187
Acknowledgement of fault codes
B0179 Acknowledgement of control word or P key on PMU (pulse) G180
Motor interface
B0180 1 = Monitoring brush length (Terminal 211=0) has responded, condition for A025 or F025 fulfilled
G186
B0181 1 = Monitoring bearing state (terminal 212=1) has responded, condition for A026 or F026 fulfilled
G186
B0182 1 = Monitoring motor fan (terminal 213=0) has responded, condition for A027 or F027 fulfilled
G186
B0183 1 = Monitoring motor temperature (terminal 213=0) has responded, condition for A028 or F028 fulfilled
G186
Temperature sensor inputs [SW 1.6 and later]
B0184 1=Alarm motor temperature 1
G185
B0185 1=Alarm motor temperature 2
G185
Alarms [SW 1.6 and later]
B0186
1=Alarm A037 (I2t motor) is pending
B0187 1=Alarm A039 (I2t power section) is pending
B0188 1=Alarm A067 (heat sink temperature) is pending
B0189
1=Alarm A067 (device fan) is pending
Torque limitation, current limitation, current controller, armature gating unit
B0190
0 = pulsating current, 1 = continuous current [SW 2.0 and later] G162
B0192
Speed limitation controller: Positive speed limit reached [SW 1.8 and later] G160
B0193
Speed limitation controller: Negative speed limit reached [SW 1.8 and later] G160
B0194
Current limitation: Positive current limit reached [SW 1.8 and later] G161