R&S ZNL Скачать руководство пользователя страница 803 | Manualshive

Страница: 803 / 1135

background image

Command reference

R&S

®

ZNL/ZNLE

803

User Manual 1178.5966.02 ─ 19

Manual operation:

See

"Channel table"

CONFigure:CHANnel:MEASure:ACTive[:STATe]

<Boolean>

If set to ON (1), only the active channel is measured. All other channels are switched
off temporarily, i.e. until

CONFigure:CHANnel:MEASure:ACTive

is set to

OFF

.

Parameters:

<Boolean>

ON (1) | OFF (0)

Manual operation:

See

"Only Active Channel On"

CONFigure:CHANnel:MEASure:ALL[:STATe]

<Boolean>

Enables or disables the sweep in all channels of the active channel setup. This com-
mand can be used in combination with

CONFigure:CHANnel<Ch>:MEASure[:

to optimize the measurement speed.

Parameters:

<Boolean>

ON | OFF
*RST:

ON

Example:

See

CONFigure:CHANnel<Ch>:MEASure[:STATe]

Manual operation:

See

"Continuous / Single"

CONFigure:CHANnel:MEASure:OPTimized

<Order>[, <Ch1>, <Ch2>, ...]

This setting tells the firmware to optimize the channel switching times for a particular
channel sweep order.

Note

that the optimization can only be applied, if

all

channels in the current setup are

in single sweep mode (

INITiate<Ch>:CONTinuous OFF

, and if there is no ongoing

sweep sequence. Any change in the current setup or a wrong sweep sequence lets the
analyzer fall back to unoptimized channel switching.

Setting parameters:

<Order>

AUTO | MANual

AUTO

Optimize the switching times for the channel order that is auto-
matically used with

(increasing order of channel

numbers).

MANual

Optimize the switching times for the channel order manually
specified using channel numbers <Ch1>, <Ch2>, ...

<Ch1>, <Ch2>, ...

Can only and must be specified for MANual optimized channel
ordering. Defines the order in which the channels are measured.
To get the optimization to work, you have to sweep the channels
manually, and in the specified order:

INIT<Ch2>

, ...

VNA command reference

«
...
801
802
803
804
805
...
»

Содержание ZNL
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZNL

Бренд: YOKOGAWA Страницы: 3

Бренд: ICS Страницы: 2

Бренд: CAISSON Страницы: 5

Бренд: Datavideo Страницы: 26

Бренд: Datcon Страницы: 84

HF scientific AccUView LED

Бренд: Watts Страницы: 40

Бренд: Hanna Instruments Страницы: 2

Smart Probes 115i

Бренд: TESTO Страницы: 17

FG-3000R Series

Бренд: Nidec Страницы: 8

Бренд: SATO KEIRYOKI Страницы: 2

Бренд: PCE Health and Fitness Страницы: 11

Бренд: Ntron Страницы: 29

Бренд: Kane Страницы: 52

Concert Monochord

Бренд: FEELTONE Страницы: 8

Бренд: Duratool Страницы: 4

WIDE ANGLE CONVERSION PORT 2

Бренд: Nauticam Страницы: 12

Бренд: Fluke Страницы: 2

Бренд: GARO Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды